What to Inspect if Your Hot Water Service is Not Functioning
What to Inspect if Your Hot Water Service is Not Functioning
Blog Article
Were you hunting for help and advice around What Would Cause My Electric Water Heater to Stop Working??
Several modern residences make use of an electrical hot water heater for their heater, as a result of its benefit and simplicity of use. Nonetheless, just like any other electric appliances, issues might occur with its use, unexpectedly. It can be truly irritating to wake up to a chilly shower as opposed to a hot one or having your bath with water that isn't warm enough and even as well warm. Whatever the case may be, hot water heater problems can be rather aggravating. Fortunately, we've made a listing of feasible solutions to your water heater problems. There are a variety of factors that might trigger most of these problems, it could be a problem with the power supply, the electric burner, or the thermostat. Before doing anything, ensure you shut off the major power supply for safety and security. Whatever the problem is, getting it repaired must not present way too much of a problem if you comply with these steps:
Call A Professional:
If after replacing all malfunctioning components and also resetting your temperature, the water heater still isn't working, you may need to call a professional plumber for a specialist point of view. The trouble with your heater could be that the hot and cold taps have been switched or it may be undersized for the amount of hot water needed in your home. Whatever the situation may be, an expert plumber would assist fix the issue.
Inspect Your Power Supply:
As fundamental as this might seem, it is very necessary. Without sufficient power, your water heater will not function. So the first thing to do when your water all of a sudden stops working is to confirm that it isn't a power problem. Check if the fuse is blown out or the breaker stumbled. If the breaker is the concern, just transform it off and on once again. Replace any broken or worn-out fuse. Examine the device with power after these adjustments to see if it's currently functioning.
Inspect Your Thermostat:
If your water heater still isn't working or the water appearing isn't warm sufficient, you may need to check the temperature level setups on your top thermostat. Make sure the circuit breaker is switched off prior to doing anything. Open up the gain access to panel as well as press the red button for temperature reset over the thermostat. This must assist heat the water. Turn the breaker back on as well as inspect if the problem has actually been settled.
Inspect the Heating Element in the Water Heater:
If it's not a power trouble, after that try having a look at your heating element if it is still functioning. Check each of your heating elements to be sure the trouble isn't with any of them. If any of them is damaged, change that part and then inspect whether the hot water is back on.
Verdict
Hot water heater problems are not constantly significant. A lot of them result from small issues like a blown fuse or damaged burner. Replacing the damaged parts should suffice. Nevertheless, if you are still unable to fix the problem, give a call to your local plumber to find to get it fixed.
What Would Cause My Electric Water Heater to Stop Working?
Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.
To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.
Basic Water Heater Troubleshooting
Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.
If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.
If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.
When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.
Conduct Advanced DIY Water Heater Troubleshooting
If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.
Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:
The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.
If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.
The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.
While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.
Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.
While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.
https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working
I found that page on No Hot Water — Water Heater Repair when browsing on the search engines. So long as you enjoyed our post kindly make sure you remember to share it. I enjoy reading our article about No Hot Water — Water Heater Repair.
Request Estimate
Report this page